Range Hood Measurement Points That Explain Airflow and Heat
Share
A range hood has one obvious job and one less obvious one. The obvious job is to collect smoke, steam, grease vapour and odours from above the hob. The less obvious job is to manage heat, both the heat rising off cooking and the heat the hood's own fan motor produces. Most of what people notice about a hood, from a weak draught to a greasy film on the cabinets, can be reasoned about by thinking about a few reference points: where air enters, where it is squeezed, where it is measured and where it exits. None of these require opening the appliance. They are mostly dimensions and observations you can make from the kitchen floor.
Reference point one: the gap over the hob
The first measurement that matters is the height of the hood's lower edge above the cooking surface. This distance sets how much of the rising plume the hood can catch before it spreads into the room. Cooking heat warms air, the warm air rises in a narrowing-ish column, and the column widens and wobbles as it climbs and as draughts push it sideways. A capture area close to the hob catches more of the plume; one placed high has to draw from a wider, more diffuse cloud, so more of the smoke escapes into the room even if the fan is running hard.
This is why the manufacturer's specified clearance range exists. The low end improves capture; the high end keeps the hood clear of flame and tall pots, and respects the appliance's own design. Users cannot invent a better figure than the range in the instructions. What they can do is check the current gap with a tape measure, compare it with the stated range, and note whether the hood has drifted out of it after a kitchen refit or a replacement hob. A hood that is too high is not faulty; it is simply working against a longer plume.
Reference point two: the entry and the filter face
The second reference point is the hood's intake, usually covered by a grease filter. The effective open area of that intake determines how easily air can be drawn in. A filter loaded with grease reduces that open area, so the fan has to work harder for less airflow, and the motor runs hotter because it is moving less air past itself. The relationship is straightforward: less free area, more resistance, less cooling flow, more heat and noise.
The filter's condition is visible from outside. Hold it up to a light after cleaning; if you cannot see through much of it, the restriction is meaningful. Most metal mesh filters are designed for washing according to the manufacturer's instructions. That is ordinary user maintenance, and it is the single most reliable way to keep the measured airflow close to the design value. A replacement filter should match the hood's specified part or approved equivalent, because filter dimensions and mesh density vary between models and a loose or over-dense filter changes the airflow.
Reference point three: the duct path
Air that passes the filter must have somewhere to go. Ducted hoods push it through a duct, and each change of direction, each length of pipe and each transition adds resistance. Two hoods with identical fans can behave very differently because one exhausts through a short straight run and the other through several bends and a long horizontal section. The reference points here are the duct diameter, the number of bends, the length and the termination.
The duct diameter must match the hood's outlet or the manufacturer's stated minimum. Reducing a duct at the outlet squeezes the same volume of air through a smaller opening, raising pressure and reducing flow. Bends cost more than straight length; elbows close together are worse than a gentle sweep. A termination hood or wall cap that is blocked, stuck or fitted with a fine insect screen that clogs will also throttle the system. These are inspection points, not repair instructions: with the power off and the hood cool, you can look at the visible duct, check that the outdoor flap opens when the fan runs, and remove obvious external obstruction where the manufacturer permits.
Reference point four: the measurement plane
When airflow is quoted or measured, it is measured somewhere. That somewhere matters. A figure taken at the hood's outlet compares poorly with a figure taken at the room's open end, and both differ from what the hob actually experiences. Practical home checks usually use the filter face as the reference plane, because that is where capture happens. A simple smoke or tissue test at that plane shows whether air is being drawn steadily across the full width, or only near one side.
Uneven pull across the filter face is a useful observation. It can come from a partially blocked filter, a duct that favours one side of the hood, or the hood's own internal design. It is a symptom, not a diagnosis of a failed part. Cleaning the filter is the first fair step; if the pattern persists and the duct is visibly clear, the remaining possibilities belong to the manufacturer's service information rather than a household trial.
Where heat enters the picture
The hood's motor and controls sit in a warm environment. Cooking heat rises toward the hood, and the motor adds its own heat as it works. Airflow is what carries that heat away, so the airflow and heat parts of the story are the same story. When the filter or duct restricts flow, the motor has less cool air passing over or around it and runs warmer. That is why a hood that seems to struggle may also sound louder and feel hot at the casing after a long session.
This does not mean every warm hood is failing. Some warmth is normal after sustained use. What matters is the pattern: a hood that has become noticeably noisier, less effective at clearing steam and warmer over the same cooking load is worth checking against the simple reference points above before assuming a component has failed. Persistent overheating, a burning smell, smoke or any sign of electrical distress is not a diagnostic puzzle; stop using the hood and have it looked at by a competent person.
Recirculating hoods use the same logic differently
A recirculating hood does not exhaust outside. It passes air through a filter, often charcoal, and returns it to the room. Its reference points are the filter face, the return grille and the condition of the odour filter. Here the heat transfer question is mostly about the motor and the filter's resistance, since there is no duct to inspect. A saturated charcoal filter raises resistance and reduces odour control at the same time. Replacement intervals come from the manufacturer, not from a general rule.
What a tape measure and a light can tell you
- Measure the vertical gap between the hood and hob, then compare it with the manufacturer's stated range in the instructions.
- Look through the cleaned grease filter toward a light to judge how open it really is.
- Note the duct diameter and count the visible bends between hood and outside termination.
- With the hood off and cool, check that the outdoor flap moves freely and is not blocked.
- Run the fan and hold a tissue or smoke source at several points across the filter face; a steady pull everywhere is the aim.
- Listen and feel for change over time: louder, weaker and warmer together is a pattern worth acting on.
None of these observations require dismantling the hood or touching wiring. They separate the common, recoverable causes, such as a greasy filter or a throttled duct, from questions that need service attention. The useful purchase is usually modest: a replacement filter of the correct specification, or a suitable cleaning product for metal mesh filters. A ducted hood may benefit from a proper wall or roof cap if the existing termination is damaged, but the correct size and type must be confirmed against the hood's instructions.
Keeping a simple record of the gap, the filter condition and the duct run helps when something starts to feel different. A hood is a machine for moving air and shedding heat, and every reference point above is a place where that movement can either be helped or hindered. Measuring first turns a vague sense that the extractor is not what it was into a short, practical list of checks.